https://redmine.replicant.us/
https://redmine.replicant.us/favicon.ico?1598461506
2020-01-27T20:34:11Z
Replicant
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7917
2020-01-27T20:34:11Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>On that device, I installed Replicant 6.0 0003, and the device booted fine.</p>
<p>Then I installed Replicant 6.0 0004 and after reboot from the recovery, I've a black screen.</p>
<p>On the UART I've things like that:<br /><pre>
====== VCELL : 405750, SOC : 96, nType : 4 ======
[Charger] nScaledVCELL : 405750000, nDesriedSOC, : 94, nMaxSOC : 114, nMinSOC : 74
* FB base addr = 0xbea70000!
* PANEL_S6E8AA0_ID_READ : 0x12, 0x8e, 0x9b.
[ omap_power_get_reset_source :47] PRM_RSTST : 0x2
<hit enter twice to activate fiq debugger>
AST_POWERON
</pre></p>
<p>But then nothing appear after AST_POWERON...</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7918
2020-01-27T20:36:36Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>As the recovery works, I looked at the load address and page size from it:<br /><pre>
unbootimg -i ../recovery-maguro.img
total image size: 8210432
kernel size: 4604340
kernel load addr: 0x80008000
ramdisk size: 3600734
ramdisk load addr: 0x81000000
2nd boot size: 0
2nd boot load addr: 0x80f00000
kernel tags addr: 0x80000100
page size: 2048
board: `'
cmdline: `androidboot.hardware=tuna'
id: e18e8c88256b849ef41ee369293b220cfcffe5a0000
</pre></p>
<p>But they look similar to the boot.img which is in the zip:<br /><pre>
unbootimg -i boot.img
total image size: 5619712
kernel size: 4604340
kernel load addr: 0x80008000
ramdisk size: 1009915
ramdisk load addr: 0x81000000
2nd boot size: 0
2nd boot load addr: 0x80f00000
kernel tags addr: 0x80000100
page size: 2048
board: `'
cmdline: `androidboot.hardware=tuna'
id: 9b90141066f527ecd3909d2ab8e383ebd995fd40000
</pre></p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7919
2020-01-27T20:37:39Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>The boot.img addresses and size also don't overlap.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7922
2020-01-29T17:35:05Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>The extracted kernel image is the same (cmp sees no difference).</p>
<p>=> It'd be a good idea to see how to add loglevel=8 and look if adding it in the boot.img is taken into account by the bootloader.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7923
2020-01-29T23:55:33Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>I've booted the Replicant 6.0 0004 RC1 boot.img with Replicant 6.0 0003 and it boots fine.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7924
2020-01-30T00:48:57Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>I got the following log:<br /><pre>
Kernel(boot.img) read success from partition no.8
Setting param.serialnr = 0x016b756d 0x14021016
Setting param.board_rev = 0x09
Setting param.cmdline = androidboot.hardware=tuna loglevel=8 fiq_debugger.console_enable=1 fiq_debugger.no_sleep=1 androidboot.serialno=016B756D14021016 androidboot.bootloader=PRIMELA03 androidboot.baseband=I9250XXLA2 lcd_bootfb=0xbea70000 mms_ts.panel_id=18 androidboot.macaddr=
Setting param.initrd_start = 0x82800000, param.initrd_size = 0xf7000
Starting kernel at 0x81808000...
�<hit enter to activate fiq debugger>
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.101-replicant (replicant@lxc-f2a85m-pro-debian) (gcc version 5.4.1 20160919 (15:5.4.1+svn241155-1) ) #1 SMP PREEMPT Sat Jan 11 02:12:08 UTC 2020
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Tuna
[ 0.000000] android_display: setting default resolution 720*1280, bpp=4
[ 0.000000] android_display: tiler1d 29491200
[ 0.000000] android_display: setting fb0.vram to 7864320
[ 0.000000] android_display: setting vram to 7864320 at address 0xbea00000
[ 0.000000] android_display: ion carveouts: 104726528 tiler2d, 0 nonsecure
[ 0.000000] omap4_total_ram_size = 0x40000000
[ 0.000000] omap4_smc_size = 0x300000
[ 0.000000] omap4_ion_heap_secure_input_size = 0x900000
[ 0.000000] omap4_ion_heap_secure_output_wfdhdcp_size = 0x0
[ 0.000000] omap4_ducati_heap_size = 0x6900000
[ 0.000000] omap4_ion_heap_tiler_mem_size = 0x0
[ 0.000000] omap4_ion_heap_nonsec_tiler_mem_size = 0x0
[ 0.000000] omap4_smc_addr = 0xbfd00000
[ 0.000000] omap4_ion_heap_secure_input_addr = 0xba300000
[ 0.000000] omap4_ion_heap_secure_output_wfdhdcp_addr = 0xba300000
[ 0.000000] omap4_ducati_heap_addr = 0xb3a00000
[ 0.000000] omap4_ion_heap_tiler_mem_addr = 0xb3a00000
[ 0.000000] omap4_ion_heap_nonsec_tiler_mem_addr = 0xb3a00000
[ 0.000000] Reserving CMA IPU + RPMSG region at address = 0xb3800000 with size = 0x7800000
[ 0.000000] cma: CMA: reserved 120 MiB at b3800000
[ 0.000000] CMA RPMSG region: address = 0xb3a00000, size = 0x8c000
[ 0.000000] CMA IPU region: address = 0xb3a8c000, size = 0x7174000
[ 0.000000] omap_ion_init: secure_input id=2 [ba300000-bac00000] size=900000
[ 0.000000] omap_ion_init: secure_output_wfdhdcp id=5 [ba300000-ba300000] size=0
[ 0.000000] omap_ion_init: tiler id=1 [b3a00000-b3a00000] size=0
[ 0.000000] omap_ion_init: nonsecure_tiler id=3 [b3a00000-b3a00000] size=0
[ 0.000000] omap_ion_init: system id=0 [0-0] size=0
[ 0.000000] omap_ion_init: tiler_reservation id=4 [0-0] size=0
[ 0.000000] Reserving 8388608 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] OMAP4460 ES1.1
[ 0.000000] SRAM: Mapped pa 0x4030d000 to va 0xfe40d000 size: 0x1000
[ 0.000000] On node 0 totalpages: 259584
[ 0.000000] free_area_init_node: node 0, pgdat c0969220, node_mem_map c09f4000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32512 pages, LIFO batch:7
[ 0.000000] HighMem zone: 1792 pages used for memmap
[ 0.000000] HighMem zone: 225024 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c11fb000 s7744 r8192 d12736 u32768
[ 0.000000] pcpu-alloc: s7744 r8192 d12736 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257536
[ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.console=ttyFIQ0 mem=1G vmalloc=768M omap_wdt.timer_margin=30 no_console_suspend androidboot.hardware=tuna loglevel=8 fiq_debugger.console_enable=1 fiq_debugger.no_sleep=1 androidboot.serialno=016B756D14021016 androidboot.bootloader=PRIMELA03 androidboot.baseband=I9250XXLA2 lcd_bootfb=0xbea70000 mms_ts.panel_id=18 androidboot.macaddr=
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] allocated 4194304 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 512MB 488MB 14MB = 1014MB total
[ 0.000000] Memory: 891796k/891796k available, 156780k reserved, 784384K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)
[ 0.000000] vmalloc : 0xc8800000 - 0xf8000000 ( 760 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0069000 ( 388 kB)
[ 0.000000] .text : 0xc0069000 - 0xc0900000 (8796 kB)
[ 0.000000] .data : 0xc0900000 - 0xc096b580 ( 430 kB)
[ 0.000000] .bss : 0xc096b5a4 - 0xc09f3e90 ( 547 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:410
[ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000061] Calibrating delay loop... 1194.24 BogoMIPS (lpj=4665344)
[ 0.023498] pid_max: default: 32768 minimum: 301
[ 0.070648] Security Framework initialized
[ 0.070648] SELinux: Initializing.
[ 0.070648] SELinux: Starting in permissive mode
[ 0.070770] Mount-cache hash table entries: 512
[ 0.070770] Initializing cgroup subsys debug
[ 0.071868] Initializing cgroup subsys cpuacct
[ 0.071929] Initializing cgroup subsys memory
[ 0.071929] Initializing cgroup subsys freezer
[ 0.071929] Initializing cgroup subsys bfqio
[ 0.072082] CPU: Testing write buffer coherency: ok
[ 0.072082] ftrace: allocating 23617 entries in 70 pages
[ 0.100219] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.100372] L310 cache controller enabled
[ 0.100372] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x5e470000, Cache size: 1048576 B
[ 0.178405] CPU1: Booted secondary processor
[ 0.209655] Brought up 2 CPUs
[ 0.209655] SMP: Total of 2 processors activated (2388.48 BogoMIPS).
[ 0.213928] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for emif_fw
[ 0.213928] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_instr
[ 0.213958] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_1
[ 0.213958] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l3_main_2
[ 0.213989] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_abe
[ 0.213989] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_cfg
[ 0.214019] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
[ 0.214019] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup
[ 0.214050] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for mpu_private
[ 0.214050] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for sl2if
[ 0.214233] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for thermal_sensor
[ 0.214233] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for usbhs_ehci
[ 0.214263] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
[ 0.214263] omap_hwmod: l4_div_ck: missing clockdomain for l4_div_ck.
[ 0.217437] _omap4_module_wait_ready: Timeout waiting for module enable (mcpdm_fck: clkctrl = 0x30002)
[ 0.219512] omap_hwmod: mcpdm: cannot be enabled (3)
[ 0.225250] print_constraints: dummy:
[ 0.225250] NET: Registered protocol family 16
[ 0.231384] GPMC revision 6.0
[ 0.231384] EMIF0 is enabled with IRQ142
[ 0.231384] EMIF1 is enabled with IRQ143
[ 0.232910] Last reset was warm software reset (PRM_RSTST=0x2)
[ 0.233062] HSI: device registered as omap_hwmod: hsi
[ 0.233306] OMAP GPIO hardware version 0.1
[ 0.234497] omap_mux_init: Add partition: #1: core, flags: 2
[ 0.236022] omap_mux_init: Add partition: #2: wkup, flags: 2
[ 0.236267] Tuna HW revision: 09 (Maguro 8th Sample), cpu OMAP4460 ES1.1
[ 0.240264] Using
[ 0.241973] _omap_mux_init_gpio: Multiple gpio paths (2) for gpio102
[ 0.242004] omap_mux_init_gpio: Could not set gpio102
[ 0.242462] _omap_mux_init_gpio: Multiple gpio paths (2) for gpio101
[ 0.242492] omap_mux_init_gpio: Could not set gpio101
[ 0.242492] _omap_mux_init_gpio: Multiple gpio paths (2) for gpio100
[ 0.242492] omap_mux_init_gpio: Could not set gpio100
[ 0.243347] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.243377] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
[ 0.243377] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.248138] OMAP DMA hardware revision 0.0
[ 0.248687] omap_rproc_get_pool: carveout memory is unavailable: 0x0, 0x0
[ 0.258239] bio: create slab <bio-0> at 0
[ 0.258605] print_constraints: vwl1271: 2000 mV
[ 0.258605] i2c-core: driver [twl] using legacy suspend method
[ 0.259429] i2c-core: driver [twl] using legacy resume method
[ 0.259429] SCSI subsystem initialized
[ 0.260681] usbcore: registered new interface driver usbfs
[ 0.261138] usbcore: registered new interface driver hub
[ 0.261230] usbcore: registered new device driver usb
[ 0.261291] i2c-gpio i2c-gpio.5: using pins 98 (SDA) and 99 (SCL)
[ 0.262451] omap_i2c omap_i2c.1: bus 1 rev4.0 at 400 kHz
[ 0.262542] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[ 0.266784] twl6030: PIH (irq 39) chaining IRQs 368..387
[ 0.268859] print_constraints: VUSB: 3300 mV normal standby
[ 0.269470] print_constraints: VMMC: 1800 mV normal standby
[ 0.270324] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[ 0.270690] print_constraints: VUSIM: 2200 mV normal standby
[ 0.270690] print_constraints: VCXIO: 1800 mV normal standby
[ 0.271301] print_constraints: VDAC: 1800 mV normal standby
[ 0.272186] print_constraints: VAUX1_6030: 3000 mV normal standby
[ 0.272918] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[ 0.272918] print_constraints: VAUX3_6030: 3100 mV normal standby
[ 0.274261] print_constraints: VDD3:
[ 0.274963] print_constraints: VMEM: at 1250 mV
[ 0.275787] print_constraints: V2V1: 2100 mV normal standby
[ 0.276519] print_constraints: VANA: 2100 mV normal standby
[ 0.277435] print_constraints: CLK32KG:
[ 0.278320] print_constraints: CLK32KAUDIO:
[ 0.278503] omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz
[ 0.278869] omap_i2c omap_i2c.3: bus 3 rev4.0 at 400 kHz
[ 0.279174] omap_i2c omap_i2c.4: bus 4 rev4.0 at 400 kHz
[ 0.279937] omap-rproc omap-rproc.0: dsp is available
[ 0.279937] omap-rproc omap-rproc.1: ipu is available
[ 0.279937] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.279937] Bluetooth: Core ver 2.16
[ 0.281524] NET: Registered protocol family 31
[ 0.281524] Bluetooth: HCI device and connection manager initialized
[ 0.281616] Bluetooth: HCI socket layer initialized
[ 0.281616] Bluetooth: L2CAP socket layer initialized
[ 0.281677] Bluetooth: SCO socket layer initialized
[ 0.282135] cfg80211: Calling CRDA to update world regulatory domain
[ 0.282287] Switching to clocksource 32k_counter
[ 0.287750] Switched to NOHz mode on CPU #0
[ 0.287780] Switched to NOHz mode on CPU #1
[ 0.298980] musb-hdrc: version 6.0, musb-dma, otg (peripheral+host)
[ 0.304687] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.304718] musb-hdrc: MHDRC RTL version 2.0
[ 0.304718] musb-hdrc: setup fifo_mode 4
[ 0.304748] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 0.304748] musb-hdrc musb-hdrc: USB OTG mode controller at fc0ab000 using DMA, IRQ 124
[ 0.305389] NET: Registered protocol family 2
[ 0.305389] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.305389] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.307220] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
[ 0.307220] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.307220] TCP reno registered
[ 0.307586] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.307586] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.308135] NET: Registered protocol family 1
[ 0.308502] Trying to unpack rootfs image as initramfs...
[ 0.388702] Freeing initrd memory: 988K
[ 0.823394] PHOENIX_LAST_TURNOFF_STS: 0x01
[ 1.944763] console [ttyFIQ0] enabled
[ 1.948577] Registered FIQ tty driver c7909b40
[ 1.953826] ram_console: got buffer at a0000000, size 200000
[ 1.953826] ram_console: uncorrectable error in header
[ 1.964935] ram_console: no valid data in buffer (sig = 0xc0c0c0c0)
[ 1.996185] console [ram-1] enabled
[ 2.010070] omap-iommu omap-iommu.0: ducati registered
[ 2.010070] omap-iommu omap-iommu.1: tesla registered
[ 2.021270] audit: initializing netlink socket (disabled)
[ 2.021270] type=2000 audit(1.984:1): initialized
[ 2.032714] highmem bounce pool size: 64 pages
[ 2.054565] NTFS driver 2.1.30 [Flags: R/O].
[ 2.058990] fuse init (API version 7.16)
[ 2.064697] msgmni has been set to 451
[ 2.068786] SELinux: Registering netfilter hooks
[ 2.076049] io scheduler noop registered
[ 2.080230] io scheduler deadline registered
[ 2.084716] io scheduler cfq registered (default)
[ 2.088012] io scheduler bfq registered
[ 2.093963] BFQ I/O-scheduler: v7r8
[ 2.098297] OMAP DSS rev 4.0
[ 2.103820] Keyboard driver not present
[ 2.108398] dsscomp: initializing.
[ 2.112396] misc dsscomp: display0=s6e8aa0
[ 2.114013] misc dsscomp: display1=hdmi_panel
[ 2.121185] misc dsscomp: found 2 displays and 4 overlays, WB overlay 1
[ 2.128295] could not allocate slot
[ 2.143157] omap-rproc omap-rproc.1: powering up ipu
[ 2.148986] virtio_rpmsg_bus virtio0: rpmsg backend virtproc probed successfully
[ 2.148986] virtio_rpmsg_bus virtio1: rpmsg backend virtproc probed successfully
[ 2.148986] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[ 2.173004] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[ 2.180877] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[ 2.188720] omap_ion_probe: adding heap secure_input of type 2 with ba300000@900000
[ 2.196868] omap_ion_probe: adding heap secure_output_wfdhdcp of type 2 with ba300000@0
[ 2.205139] omap_ion_probe: adding heap tiler of type 4 with b3a00000@0
[ 2.211914] omap_ion_probe: adding heap nonsecure_tiler of type 4 with b3a00000@0
[ 2.219665] omap_ion_probe: adding heap system of type 0 with 0@0
[ 2.225921] omap_ion_probe: adding heap tiler_reservation of type 5 with 0@0
[ 2.239837] brd: module loaded
[ 2.246307] loop: module loaded
[ 2.250122] zram: Created 1 device(s) ...
[ 2.255310] input: barometer as /devices/virtual/input/input0
[ 2.261413] sec_jack_probe : Registering jack driver
[ 2.267211] i2c i2c-4: mpu_probe: 0
[ 2.332611] i2c i2c-4: Installing irq using 205
[ 2.332611] i2c i2c-4: Module Param interface = mpuirq
[ 2.332611] i2c-core: driver [mpu3050] using legacy suspend method
[ 2.349304] i2c-core: driver [mpu3050] using legacy resume method
[ 2.355651] mpu_init: Probe name mpu3050
[ 2.355651] i2c i2c-4: bma250_mod_probe: bma250
[ 2.355651] i2c i2c-4: Installing Accel irq using 282
[ 2.414550] i2c i2c-4: mpu3050: +bma250
[ 2.418609] bma250_mod_init: Probe name bma250_mod
[ 2.423614] i2c i2c-4: yas530_mod_probe: yas530
[ 2.423614] i2c i2c-4: Installing Compass irq using 336
[ 2.457702] i2c i2c-4: mpu3050: +yas530
[ 2.457702] yas530_mod_init: Probe name yas530_mod
HSI driver version 0.4.3
[ 3.393310] omap_hsi omap_hsi.0: Registering IRQ hsi_p1_mpu (99)
[ 3.399475] omap_hsi omap_hsi.0: HSI port 1 initialized
[ 3.404998] omap_hsi omap_hsi.0: Registering IRQ hsi_dma_mpu (103)
[ 3.411529] omap_hsi omap_hsi.0: HSI Hardware REVISION 0x50043101
[ 3.419830] omap_hsi omap_hsi.0: Cannot set HSI FClk to default value: 96000000. Will retry on next open
[ 3.433929] Tuna ASoC init
[ 3.442474] twl6040-codec twl6040-codec: couldn't get VDDHF regulator -19
[ 3.478118] asoc: null-codec-dai <-> MultiMedia1 mapping ok
[ 3.485260] asoc: null-codec-dai <-> MultiMedia2 mapping ok
[ 3.492828] asoc: null-codec-dai <-> Voice mapping ok
[ 3.499694] asoc: null-codec-dai <-> Tones mapping ok
[ 3.506530] asoc: null-codec-dai <-> Vibra mapping ok
[ 3.512664] asoc: null-codec-dai <-> MODEM mapping ok
[ 3.518737] asoc: null-codec-dai <-> MultiMedia1 LP mapping ok
[ 3.526702] asoc: FM Digital <-> omap-mcbsp-dai.1 mapping ok
[ 3.533935] asoc: twl6040-dl1 <-> mcpdm-dl mapping ok
[ 3.540588] asoc: dit-hifi <-> omap-mcasp-dai mapping ok
[ 3.548553] twl6040-codec twl6040-codec: ASoC: Failed to create Aux/FM Stereo In debugfs file
[ 3.558349] asoc: twl6040-dl1 <-> mcpdm-dl1 mapping ok
[ 3.564697] asoc: twl6040-ul <-> mcpdm-ul1 mapping ok
[ 3.570800] asoc: twl6040-dl2 <-> mcpdm-dl2 mapping ok
[ 3.576690] mmc0: new high speed MMC card at address 0001
[ 3.577239] asoc: twl6040-vib <-> mcpdm-vib mapping ok
[ 3.578216] asoc: Bluetooth <-> omap-mcbsp-dai.0 mapping ok
[ 3.579193] asoc: Bluetooth <-> omap-mcbsp-dai.0 mapping ok
[ 3.580230] asoc: FM Digital <-> omap-mcbsp-dai.1 mapping ok
[ 3.581237] asoc: MODEM <-> omap-mcbsp-dai.1 mapping ok
[ 3.582214] asoc: null-codec-dai <-> omap-abe-vxrec-dai mapping ok
[ 3.584197] input: Tuna Headset Jack as /devices/platform/soc-audio/sound/card0/input5
[ 3.625152] mmcblk0: mmc0:0001 VYL00M 14.6 GiB
[ 3.626800] asoc: hdmi-audio-codec <-> hdmi-audio-dai mapping ok
[ 3.627349] ALSA device list:
[ 3.627380] #0: TI OMAP4 Board
[ 3.627380] #1: OMAP4HDMI
[ 3.627502] GACT probability NOT on
[ 3.627532] Mirror/redirect action on
[ 3.627532] u32 classifier
[ 3.627563] Actions configured
[ 3.627563] Netfilter messages via NETLINK v0.30.
[ 3.627655] nf_conntrack version 0.5.0 (15869 buckets, 63476 max)
[ 3.629364] ctnetlink v0.93: registering with nfnetlink.
[ 3.629394] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 3.629425] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 3.629943] xt_time: kernel timezone is -0000
[ 3.632751] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.632965] arp_tables: (C) 2002 David S. Miller
[ 3.633026] TCP bic registered
[ 3.633026] TCP cubic registered
[ 3.633056] TCP westwood registered
[ 3.633056] TCP htcp registered
[ 3.633056] Initializing XFRM netlink socket
[ 3.634368] NET: Registered protocol family 10
[ 3.643707] Mobile IPv6
[ 3.643737] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.644134] IPv6 over IPv4 tunneling driver
[ 3.651977] NET: Registered protocol family 17
[ 3.652008] NET: Registered protocol family 15
[ 3.652282] Bluetooth: RFCOMM TTY layer initialized
[ 3.652313] Bluetooth: RFCOMM socket layer initialized
[ 3.652343] Bluetooth: RFCOMM ver 1.11
[ 3.652343] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.652374] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.652557] NET: Registered protocol family 35
[ 3.653320] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 3.785461] ThumbEE CPU extension supported.
[ 3.785522] mmcblk0boot0: mmc0:0001 VYL00M partition 1 512 KiB
[ 3.795959] Registering SWP/SWPB emulation handler
[ 3.795989] mmcblk0boot1: mmc0:0001 VYL00M partition 2 512 KiB
[ 3.806945] Registering SDIV/UDIV emulation handler
[ 3.817657] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13
[ 3.825714] Reprogramming LPDDR2 timings to 400000000 Hz
[ 3.831481] sr_init: No PMIC hook to init smartreflex
[ 3.836730] mmcblk0boot1: unknown partition table
[ 3.836883] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
[ 3.837066] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
[ 3.837249] smartreflex smartreflex.2: omap_sr_probe: SmartReflex driver initialized
[ 3.865386] SmartReflex class 1.5 driver: initialized (86400000ms)
[ 3.872161] mmcblk0boot0: unknown partition table
[ 3.872436] Power Management for TI OMAP4.
[ 3.872589] OMAP4 PM: Static dependency added between MPUSS and DUCATI <-> L4_PER/CFG and L3_1.
[ 3.890350] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:0 (mask:ff)
[ 3.899749] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:1 (mask:ff)
[ 3.909057] sr_class1p5_calib_work: mpu: Calibration complete: Voltage:Nominal=1203000 Calib=990000 margin=0
[ 3.919219] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:2 (mask:ff)
[ 3.928619] sr_class1p5_calib_work: core: Calibration complete: Voltage:Nominal=1127000 Calib=1063480 margin=13000
[ 3.939300] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:3 (mask:ff)
[ 3.948699] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:4 (mask:ff)
[ 3.957916] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:5 (mask:ff)
[ 3.967224] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:6 (mask:ff)
[ 3.976501] HSI DRIVER BUS : hsi_bus_match SUCCESS : ctrl:0 (mask:ffffffff), port:0, ch:7 (mask:ff)
[ 3.985717] sr_class1p5_calib_work: iva Stop sampling: Voltage Nominal=950000 samples=3
[ 3.994049] sr_class1p5_calib_work: iva: Calibration complete: Voltage:Nominal=950000 Calib=860920 margin=13000
[ 4.016998] clock: disabling unused clocks to save power
[ 4.023468] cannot apply mgr(lcd) on inactive device
[ 4.028625] omapfb omapfb: failed to apply dispc config
[ 4.033996] cannot apply mgr(tv) on inactive device
[ 4.039001] omapfb omapfb: failed to apply dispc config
[ 4.044372] cannot apply mgr(lcd2) on inactive device
[ 4.049530] omapfb omapfb: failed to apply dispc config
[ 4.057800] regulator_init_complete: VDAC: disabling
[ 4.063873] regulator_init_complete: VUSB: disabling
[ 4.070251] fsa9480 4-0025: cable detect change, from 'unknown/none' to 'jig'
AST_POWERON
</pre></p>
<p>By following this howto: <a class="external" href="https://redmine.replicant.us/projects/replicant/wiki/GalaxyNexusI9250SerialConsole#Without-patching-the-kernel-on-Replicant-6">https://redmine.replicant.us/projects/replicant/wiki/GalaxyNexusI9250SerialConsole#Without-patching-the-kernel-on-Replicant-6</a></p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7925
2020-01-30T01:05:00Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>As expected, installing the 0004 RC1, and using the 0003 boot.img didn't boot.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7926
2020-01-30T01:07:00Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>Given all the above, it's probably safe to assume that the problem is not in the kernel and build a kernel with the patches to get a real serial console as per <a class="external" href="https://redmine.replicant.us/projects/replicant/wiki/GalaxyNexusI9250SerialConsole#Real-serial-console-by-patching-the-kernel">https://redmine.replicant.us/projects/replicant/wiki/GalaxyNexusI9250SerialConsole#Real-serial-console-by-patching-the-kernel</a></p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7927
2020-01-30T19:51:44Z
Kurtis Hanna
Kurtis@riseup.net
<ul></ul><p>I assume this doesn't help very much, but just in case you'd like to obtain some logs from LineageOS in order to compare them to the rc-1 image here's the most reliable source for maguro LOS Roms that I know of: <a class="external" href="https://web.archive.org/web/20180125105715/https://download.lineageos.org/maguro">https://web.archive.org/web/20180125105715/https://download.lineageos.org/maguro</a></p>
<p>I didn't see it posted elsewhere on redmine.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7931
2020-02-13T17:25:52Z
Graham Cobb
<ul></ul><p>I see a similar black screen with espressowifi. Let me know if there is any information I can gather which would be useful.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7934
2020-02-14T23:26:24Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>Thanks a lot to <code>putti</code> on IRC for giving me the way more simple idea of building an -eng image.<br />While it takes a lot of time to recompile an image, it's way easier to debug since we now have adb root during boot, including logcat etc.</p>
<p>So adb logcat -b main gives:<br /><pre>
01-01 00:08:21.297 1106 1106 E RadioService: couldn't load radio module radio.primary (No such file or directory)
01-01 00:08:21.350 135 135 I ServiceManager: service 'media.audio_flinger' died
01-01 00:08:21.350 135 135 I ServiceManager: service 'media.player' died
01-01 00:08:21.350 135 135 I ServiceManager: service 'media.resource_manager' died
01-01 00:08:21.350 135 135 I ServiceManager: service 'media.camera' died
01-01 00:08:21.350 135 135 I ServiceManager: service 'media.audio_policy' died
01-01 00:08:21.350 135 135 I ServiceManager: service 'media.sound_trigger_hw' died
01-01 00:08:21.350 135 135 I ServiceManager: service 'media.radio' died
01-01 00:08:25.463 1152 1152 I Netd : Netd 1.0 starting
01-01 00:08:25.464 1152 1152 I QtiConnectivityAdapter: Failed to open libconnctrl, some features may not be present.
01-01 00:08:25.464 1152 1152 D TetherController: Setting IP forward enable = 0
01-01 00:08:25.535 1153 1153 I SurfaceFlinger: SurfaceFlinger is starting
01-01 00:08:25.535 1153 1153 I SurfaceFlinger: SurfaceFlinger's main thread ready to run. Initializing graphics H/W...
01-01 00:08:25.535 1153 1153 D libEGL : UID:1000 EUID:1000
01-01 00:08:25.535 1153 1153 D libEGL : ro.zygote.disable_gl_preload not set, EGL overrides disabled
01-01 00:08:25.540 1153 1153 D libEGL : loaded /system/lib/egl/libGLES_mesa.so
01-01 00:08:25.679 1153 1153 W gralloc : page flipping not supported (yres_virtual=1280, requested=2560)
01-01 00:08:25.679 1153 1153 I gralloc : using (fd=12)
01-01 00:08:25.679 1153 1153 I gralloc : id = omapfb
01-01 00:08:25.679 1153 1153 I gralloc : xres = 720 px
01-01 00:08:25.679 1153 1153 I gralloc : yres = 1280 px
01-01 00:08:25.679 1153 1153 I gralloc : xres_virtual = 720 px
01-01 00:08:25.679 1153 1153 I gralloc : yres_virtual = 1280 px
01-01 00:08:25.679 1153 1153 I gralloc : bpp = 16
01-01 00:08:25.679 1153 1153 I gralloc : r = 11:5
01-01 00:08:25.679 1153 1153 I gralloc : g = 5:6
01-01 00:08:25.679 1153 1153 I gralloc : b = 0:5
01-01 00:08:25.679 1153 1153 I gralloc : width = 58 mm (315.310333 dpi)
01-01 00:08:25.679 1153 1153 I gralloc : height = 102 mm (318.745087 dpi)
01-01 00:08:25.679 1153 1153 I gralloc : refresh rate = 59.14 Hz
01-01 00:08:25.684 1153 1153 E ti_hwc : Composer HAL failed to load compatible Graphics HAL
01-01 00:08:25.684 1153 1153 E SurfaceFlinger: composer device failed to initialize (Invalid argument)
01-01 00:08:25.684 1153 1153 I SurfaceFlinger: EGL information:
01-01 00:08:25.684 1153 1153 I SurfaceFlinger: vendor : Android
01-01 00:08:25.684 1153 1153 I SurfaceFlinger: version : 1.4 Android META-EGL
01-01 00:08:25.684 1153 1153 I SurfaceFlinger: extensions: EGL_KHR_get_all_proc_addresses EGL_ANDROID_presentation_time EGL_KHR_swap_buffers_with_damage EGL_KHR_image_base EGL_KHR_gl_texture_2D_image EGL_KHR_gl_texture_3D_image EGL_KHR_gl_texture_cubemap_image EGL_KHR_gl_renderbuffer_image EGL_KHR_reusable_sync EGL_KHR_fence_sync EGL_KHR_create_context EGL_KHR_surfaceless_context EGL_ANDROID_image_native_buffer EGL_KHR_wait_sync EGL_ANDROID_recordable
01-01 00:08:25.684 1153 1153 I SurfaceFlinger: Client API: OpenGL_ES
01-01 00:08:25.684 1153 1153 I SurfaceFlinger: EGLSurface: 5-6-5-0, config=0xb56ed740
01-01 00:08:25.685 1153 1153 F SurfaceFlinger: EGLContext creation failed
01-01 00:08:25.686 141 141 I DEBUG : property debug.db.uid not set; NOT waiting for gdb.
01-01 00:08:25.686 141 141 I DEBUG : HINT: adb shell setprop debug.db.uid 100000
01-01 00:08:25.686 141 141 I DEBUG : HINT: adb forward tcp:5039 tcp:5039
01-01 00:08:26.100 1154 1154 V MediaUtils: physMem: 1040437248
01-01 00:08:26.100 1154 1154 V MediaUtils: requested limit: 676284180
01-01 00:08:26.100 1154 1154 V MediaUtils: actual limit: 676284180
01-01 00:08:26.101 1154 1154 V MediaUtils: original limits: 4294967295/4294967295
01-01 00:08:26.101 1154 1154 V MediaUtils: new limits: 676284180/4294967295
01-01 00:08:26.109 1154 1154 I mediaserver: ServiceManager: 0xb5fce120
01-01 00:08:26.109 1154 1154 I AudioFlinger: Using default 3000 mSec as standby time.
01-01 00:08:26.110 1154 1154 E BatteryNotifier: batterystats service unavailable!
01-01 00:08:26.110 1154 1154 E BatteryNotifier: batterystats service unavailable!
01-01 00:08:26.110 1154 1154 I CameraService: CameraService started (pid=1154)
01-01 00:08:26.110 1154 1154 I CameraService: CameraService process starting
01-01 00:08:26.110 1154 1154 E BatteryNotifier: batterystats service unavailable!
01-01 00:08:26.110 1154 1154 E BatteryNotifier: batterystats service unavailable!
01-01 00:08:26.111 1154 1154 E CameraService: Could not load camera HAL module: -2 (No such file or directory)
01-01 00:08:26.117 1154 1154 I AudioPolicyService: AudioPolicyService CSTOR in new mode
01-01 00:08:26.118 1154 1154 I APM::ConfigParsingUtils: loadAudioPolicyConfig() loaded /system/etc/audio_policy.conf
01-01 00:08:26.148 1154 1154 D Audio-RIL-Interface: OpenClient_RILD()
01-01 00:08:26.148 1154 1154 D Audio-RIL-Interface: RegisterUnsolicitedHandler(0xb5fc6450, 11017, 0xb6072ee1)
01-01 00:08:26.148 1154 1154 I AudioFlinger: loadHwModule() Loaded primary audio interface from Tuna audio HW HAL (audio) handle 1
01-01 00:08:26.148 1154 1154 I AudioFlinger: openOutput(), module 1 Device 2, SamplingRate 44100, Format 0x000001, Channels 3, flags 2
01-01 00:08:26.148 1154 1154 I AudioFlinger: AudioStreamOut::open(), mHalFormatIsLinearPcm = 1
01-01 00:08:26.148 1154 1154 I AudioFlinger: HAL output buffer size 144 frames, normal sink buffer size 896 frames
01-01 00:08:26.159 1154 1154 I BufferProvider: found effect "Multichannel Downmix To Stereo" from The Android Open Source Project
01-01 00:08:26.171 1154 1154 E MonoPipe: Failed to fetch local time frequency when constructing a MonoPipe (res = -32). getNextWriteTimestamp calls will be non-functional
01-01 00:08:26.171 1154 1154 I AudioFlinger: Using module 1 has the primary audio interface
01-01 00:08:26.179 1154 1185 I AudioFlinger: AudioFlinger's thread 0xb4480000 ready to run
01-01 00:08:26.180 1154 1185 E AudioFlinger: no wake lock to update!
01-01 00:08:26.181 1154 1154 I AudioFlinger: openOutput(), module 1 Device 2, SamplingRate 44100, Format 0x000001, Channels 3, flags 8
01-01 00:08:26.181 1154 1154 I AudioFlinger: AudioStreamOut::open(), mHalFormatIsLinearPcm = 1
01-01 00:08:26.181 1154 1154 I AudioFlinger: HAL output buffer size 896 frames, normal sink buffer size 896 frames
01-01 00:08:26.187 1154 1186 I AudioFlinger: AudioFlinger's thread 0xb4040000 ready to run
01-01 00:08:26.189 1154 1186 E AudioFlinger: no wake lock to update!
01-01 00:08:26.195 1154 1187 I AudioFlinger: AudioFlinger's thread 0xb3ec0000 ready to run
01-01 00:08:26.197 1154 1154 I bt_a2dp_hw: adev_open: adev_open in A2dp_hw module
01-01 00:08:26.197 1154 1154 I AudioFlinger: loadHwModule() Loaded a2dp audio interface from A2DP Audio HW HAL (audio) handle 5
01-01 00:08:26.198 1154 1154 I r_submix: adev_open(name=audio_hw_if)
01-01 00:08:26.198 1154 1154 I r_submix: adev_init_check()
01-01 00:08:26.198 1154 1154 I AudioFlinger: loadHwModule() Loaded r_submix audio interface from Wifi Display audio HAL (audio) handle 6
01-01 00:08:26.198 1154 1154 D r_submix: adev_open_input_stream(addr=0)
01-01 00:08:26.198 1154 1154 D r_submix: submix_audio_device_create_pipe_l(addr=0, idx=9)
01-01 00:08:26.198 1154 1154 D r_submix: now using address 0 for route 9
01-01 00:08:26.199 1154 1188 I AudioFlinger: AudioFlinger's thread 0xb3ec0000 ready to run
01-01 00:08:26.199 1154 1154 D r_submix: adev_close_input_stream()
01-01 00:08:26.199 1154 1154 D r_submix: submix_audio_device_release_pipe_l(idx=9) addr=0
01-01 00:08:26.199 1154 1154 D r_submix: submix_audio_device_destroy_pipe_l(): pipe destroyed
01-01 00:08:26.201 1154 1154 I AudioFlinger: loadHwModule() Loaded usb audio interface from USB audio HW HAL (audio) handle 8
01-01 00:08:26.202 1154 1154 E SoundTriggerHwService: couldn't load sound trigger module sound_trigger.primary (No such file or directory)
01-01 00:08:26.210 1154 1154 I RadioService: RadioService
01-01 00:08:26.210 1154 1154 I RadioService: onFirstRef
01-01 00:08:26.210 1154 1154 E RadioService: couldn't load radio module radio.primary (No such file or directory)
01-01 00:08:26.231 135 135 I ServiceManager: service 'media.audio_flinger' died
01-01 00:08:26.231 135 135 I ServiceManager: service 'media.player' died
01-01 00:08:26.231 135 135 I ServiceManager: service 'media.resource_manager' died
01-01 00:08:26.231 135 135 I ServiceManager: service 'media.camera' died
01-01 00:08:26.232 135 135 I ServiceManager: service 'media.audio_policy' died
01-01 00:08:26.232 135 135 I ServiceManager: service 'media.sound_trigger_hw' died
01-01 00:08:26.232 135 135 I ServiceManager: service 'media.radio' died
</pre></p>
<p>Maybe this is due to some wrong rebase?<br />Note that after enabling Ethernet, the built images booted on maguro at that time.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7935
2020-02-15T02:19:50Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><pre>
#!/bin/sh
# In the cases where this work is copyrightable, it falls under the AGPLv3
# or later license that is available here:
# https://www.gnu.org/licenses/agpl-3.0.txt
# with the following attribution(s):
# Copyright (C) 2020 Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
repos="
build \
manifest \
bootable/recovery \
external/boringssl \
external/heimdall \
frameworks/av \
frameworks/base \
frameworks/native \
hardware/broadcom/wlan \
hardware/libhardware \
hardware/libhardware_legacy \
hardware/ti/omap4 \
libcore \
packages/apps/Browser \
packages/apps/LegacyCamera \
packages/apps/RepWifi \
packages/apps/ReplicantWallpapers \
packages/apps/Settings \
packages/apps/SetupWizard \
packages/apps/ThemeChooser \
packages/providers/ContactsProvider \
system/core \
vendor/replicant \
vendor/cmsdk \
external/drm_gralloc \
external/llvm \
external/mesa3d \
external/parameter-framework \
external/protobuf \
prebuilts/ndk \
prebuilts/sdk \
sdk \
toolchain/src/binutils \
toolchain/src/gcc \
toolchain/src/jack \
toolchain/src/jill \
kernel/samsung/smdk4412 \
kernel/samsung/tuna \
kernel/samsung/espresso10 \
device/samsung/i9100 \
device/samsung/n7000 \
device/samsung/i9300 \
device/samsung/i9305 \
device/samsung/n7100 \
device/samsung/n5100 \
device/samsung/n5110 \
device/samsung/maguro \
device/samsung/tuna \
device/samsung/espressowifi \
device/samsung/espresso3g \
device/samsung/galaxys2-common \
device/samsung/smdk4412-common \
device/samsung/kona-common \
hardware/tinyalsa-audio \
"
# repos="
# ${repos} \
# hardware/ril/samsung-ril \
# external/libsamsung-ipc \
# "
repos="
${repos} \
hardware/replicant/libsamsung-ril \
hardware/replicant/libsamsung-ipc \
"
# external/chromium-webview \
for repo in $repos ; do
echo "${repo}: $(git -C ${repo} diff replicant-6.0-0003..replicant-6.0-0004-rc1 | wc -l)"
done
</pre><br />gives:<br /><pre>
build: 289
manifest: 509
bootable/recovery: 0
external/boringssl: 0
external/heimdall: 0
frameworks/av: 1410
frameworks/base: 106989
frameworks/native: 623
hardware/broadcom/wlan: 0
hardware/libhardware: 0
hardware/libhardware_legacy: 0
hardware/ti/omap4: 0
libcore: 0
packages/apps/Browser: 1452
packages/apps/LegacyCamera: 0
packages/apps/RepWifi: 0
packages/apps/ReplicantWallpapers: 0
packages/apps/Settings: 10677
packages/apps/SetupWizard: 106
packages/apps/ThemeChooser: 108
packages/providers/ContactsProvider: 135
system/core: 245
vendor/replicant: 338
vendor/cmsdk: 438
external/drm_gralloc: 35
external/llvm: 0
external/mesa3d: 0
external/parameter-framework: 0
external/protobuf: 0
prebuilts/ndk: 0
prebuilts/sdk: 0
sdk: 0
toolchain/src/binutils: 0
toolchain/src/gcc: 4021
toolchain/src/jack: 0
toolchain/src/jill: 0
kernel/samsung/smdk4412: 25791
kernel/samsung/tuna: 36
kernel/samsung/espresso10: 26
device/samsung/i9100: 0
device/samsung/n7000: 0
device/samsung/i9300: 18
device/samsung/i9305: 0
device/samsung/n7100: 18
device/samsung/n5100: 19
device/samsung/n5110: 0
device/samsung/maguro: 18
device/samsung/tuna: 0
device/samsung/espressowifi: 0
device/samsung/espresso3g: 51
device/samsung/galaxys2-common: 18
device/samsung/smdk4412-common: 0
device/samsung/kona-common: 0
hardware/tinyalsa-audio: 0
hardware/replicant/libsamsung-ril: 742
hardware/replicant/libsamsung-ipc: 799
</pre>
<p>And we have:<br /><pre>
$ repo grep sound_trigger | sed 's#:.*##' | sort -u
external/sepolicy/service_contexts
frameworks/av/include/soundtrigger/ISoundTrigger.h
frameworks/av/include/soundtrigger/ISoundTriggerHwService.h
frameworks/av/include/soundtrigger/SoundTriggerCallback.h
frameworks/av/include/soundtrigger/SoundTrigger.h
frameworks/av/services/soundtrigger/SoundTriggerHwService.cpp
frameworks/av/services/soundtrigger/SoundTriggerHwService.h
frameworks/av/soundtrigger/ISoundTrigger.cpp
frameworks/av/soundtrigger/ISoundTriggerHwService.cpp
frameworks/av/soundtrigger/SoundTrigger.cpp
frameworks/base/core/java/android/hardware/soundtrigger/SoundTrigger.java
frameworks/base/core/jni/android_hardware_SoundTrigger.cpp
hardware/libhardware/include/hardware/sound_trigger.h
hardware/libhardware/modules/soundtrigger/Android.mk
hardware/libhardware/modules/soundtrigger/sound_trigger_hw.c
hardware/qcom/audio/default/hal/Android.mk
hardware/qcom/audio/default/hal/audio_extn/audio_extn.h
hardware/qcom/audio/default/hal/audio_extn/soundtrigger.c
hardware/qcom/audio/default/hal/audio_extn/sound_trigger_prop_intf.h
hardware/qcom/audio/default/hal/audio_hw.c
hardware/qcom/audio/default/msm8909/hal/Android.mk
hardware/qcom/audio/default/msm8909/hal/audio_extn/audio_extn.c
hardware/qcom/audio/default/msm8909/hal/audio_extn/audio_extn.h
hardware/qcom/audio/default/msm8909/hal/audio_extn/soundtrigger.c
hardware/qcom/audio/default/msm8909/hal/audio_hw.c
hardware/qcom/audio/default/msm8909/hal/msm8916/platform.c
hardware/qcom/audio/default/msm8909/hal/msm8960/platform.c
hardware/qcom/audio/default/msm8909/hal/msm8974/platform.c
hardware/qcom/audio/default/msm8909/hal/platform_api.h
system/media/audio/include/system/sound_trigger.h
</pre></p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7942
2020-02-20T14:11:45Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul><li><strong>File</strong> <a href="/attachments/1657">main.log</a> <a class="icon-only icon-download" title="Download" href="/attachments/download/1657/main.log">main.log</a> added</li></ul>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7943
2020-02-20T14:12:13Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>I've attached the log of a first boot with a patched (for adb root) boot.img</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7944
2020-02-20T14:15:58Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>The fact that the display is black + the fact that this happens very early:<br /><pre>
01-01 00:40:21.958 136 136 E ti_hwc : Composer HAL failed to load compatible Graphics HAL
01-01 00:40:21.958 136 136 E SurfaceFlinger: composer device failed to initialize (Invalid argument)
</pre></p>
<p>seem to indicate some issue with graphics.</p>
<p>I'll try to patch the boot.img to use libagl by default to see if it changes something.</p>
<p>It might also be related to a color format:<br /><pre>
01-01 00:40:21.959 136 136 I SurfaceFlinger: EGLSurface: 5-6-5-0, config=0xb56ed740
01-01 00:40:21.959 136 136 F SurfaceFlinger: EGLContext creation failed
</pre></p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=7945
2020-02-20T14:22:08Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul></ul><p>Going back to libagl like that:<br /><pre>
$ adb root
$ adb shell
root@maguro:/ # androidsw.sh
Remounting system partition as writable...
Enabling Android software renderer...
Syncing filesystem...
Remounting system partition as read-only...
Syncing filesystem...
Android software renderer will be enabled after we reboot now...
Error type 2
android.util.AndroidException: Can't connect to activity manager; is the system running?
at com.android.commands.am.Am.onRun(Am.java:353)
at com.android.internal.os.BaseCommand.run(BaseCommand.java:47)
at com.android.commands.am.Am.main(Am.java:100)
at com.android.internal.os.RuntimeInit.nativeFinishInit(Native Method)
at com.android.internal.os.RuntimeInit.main(RuntimeInit.java:258)
root@maguro:/ # reboot
</pre></p>
<p>is sufficent to make the device boot.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=8021
2020-05-04T02:35:22Z
Kurtis Hanna
Kurtis@riseup.net
<ul></ul><p>Not sure if this helps at all, but I'm relaying it from the replicant irc in the assumption that it applies to this ticket:</p>
<p>David said that, on Replicant 6, RGB555 is used throughout the entire stack.</p>
<p>Denis said we probably need RGB565 instead of RGB555 on Replicant 6 because neither omap nor exynos have the RGB555 DRM database format.</p>
<p><a class="external" href="https://drmdb.emersion.fr/formats?driver=omapdrm">https://drmdb.emersion.fr/formats?driver=omapdrm</a><br /><a class="external" href="https://drmdb.emersion.fr/formats?driver=exynos">https://drmdb.emersion.fr/formats?driver=exynos</a></p>
<p>Denis then said that for Replicant 6 his recent patches probably unbroke booting on the Galaxy Nexus but broke booting on other devices.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=8128
2020-06-27T03:44:35Z
Kurtis Hanna
Kurtis@riseup.net
<ul><li><strong>Blocks</strong> <i><a class="issue tracker-3 status-27 priority-21 priority-default closed" href="/issues/1960">Issue #1960</a>: Build release candidate image for 6.0 0004</i> added</li></ul>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=8130
2020-06-27T06:05:04Z
Kurtis Hanna
Kurtis@riseup.net
<ul><li><strong>Status</strong> changed from <i>New</i> to <i>Closed</i></li><li><strong>Resolution</strong> set to <i>fixed</i></li></ul><p>I believe that this was fixed with this patch <a class="external" href="https://git.replicant.us//contrib/GNUtoo/frameworks_native/commit/?id=108a3f6c45c354116578f2d4bf6979c3b8aa0fb8">https://git.replicant.us//contrib/GNUtoo/frameworks_native/commit/?id=108a3f6c45c354116578f2d4bf6979c3b8aa0fb8</a></p>
<p>This email suggests heavily that this bug has been fixed: <a class="external" href="https://lists.osuosl.org/pipermail/replicant/2020-June/002861.html">https://lists.osuosl.org/pipermail/replicant/2020-June/002861.html</a></p>
<p>I'm resolving this ticket as fixed.</p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=8131
2020-06-27T06:15:51Z
Kurtis Hanna
Kurtis@riseup.net
<ul><li><strong>Status</strong> changed from <i>Closed</i> to <i>Resolved</i></li></ul>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=8219
2020-07-24T23:29:48Z
Kurtis Hanna
Kurtis@riseup.net
<ul></ul><p>The 6.0 0004 rc2 Roms, which have this fix included in them, can be obtained here: <a class="external" href="https://ftp.osuosl.org/pub/replicant/images/replicant-6.0/0004-rc2/">https://ftp.osuosl.org/pub/replicant/images/replicant-6.0/0004-rc2/</a></p>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=8478
2020-12-07T18:02:49Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul><li><strong>Related to</strong> <i><a class="issue tracker-3 status-3 priority-21 priority-default" href="/issues/2171">Issue #2171</a>: OMAP device: very slow llvmpipe</i> added</li></ul>
Replicant - Issue #1994: Black screen after installing the Replicant 6.0 0004 RC1 images
https://redmine.replicant.us/issues/1994?journal_id=8594
2021-02-27T08:41:24Z
Denis 'GNUtoo' Carikli
GNUtoo@cyberdimension.org
<ul><li><strong>Device</strong> <i>Galaxy Nexus (GT-I9250)</i> added</li></ul>