h1. GTIN7000Bootloader
h2. Boot log
�
Welcome to Samsung Primitive Bootloader.
build time: Nov 11 2011 15:10:05
current time: ff/1f/3 3f:7f:70
[set_mmc_ocr] Sector Mode
[hsmmc_init] MMC card is detected
Product Name : VYL00M
ext_csd
card_size: 15028
Total Card Size: 15029 MByte
mmc_init: card initialization completed!
pbl found bootable sbl in #53248.
jump to sbl 0x4d400000.
Secondary Bootloader v3.1 version.
Copyright (C) 2011 System S/W Group. Samsung Electronics Co., Ltd.
Board: C1 REV 02 / Apr 25 2012 00:55:25
current time: ff/1f/3 3f:7f:71
booting code=0xc0c0c0c0
[set_mmc_ocr] Sector Mode
[hsmmc_init] MMC card is detected
Product Name : VYL00M
CID:150100 56594c30 304d1999 c829381f
ext_csd
card_size: 15028
Total Card Size: 15029 MByte
Total Sector Count: 30777344
MoviNand Initialization Complete!
===== PARTITION INFORMATION =====
ID DEVICE FIRST UNIT NO. UNITS
GANG (0x0) MMC 0 0
BOOT (0x1) MMC 0 0
EFS (0x4) MMC 8192 40960
SBL1 (0x2) MMC 49152 2560
SBL2 (0x3) MMC 53248 2560
PARAM (0x5) MMC 57344 16384
KERNEL (0x6) MMC 73728 16384
RECOVERY (0x7) MMC 90112 16384
CACHE (0x8) MMC 106496 409600
MODEM (0x9) MMC 516096 32768
FACTORYFS (0xa) MMC 548864 1744896
DATAFS (0xb) MMC 2293760 4194304
UMS (0xc) MMC 6488064 23232512
HIDDEN (0xd) MMC 29720576 1048576
loke_init: j4fs_open..success
CHECKSUM_HEADER_SECTOR :42
offset:42, size:1024
Not Need Movinand Checksum
load_lfs_parameters valid magic code and version.
switch_sel_str='1'
load_debug_level: read debug level successfully(0x574f4c44)...LOW
init_ddi_data: usable ddi data.
init_fuel_gauge : not por status
fuel_gauge_get_version: [1]=19, [0]=d3
init_fuel_gauge: vcell = 4058 mV, vfocv = 4131 mV, soc = 96
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
9172 = (403800 - 329011)*12264/100000
[1] 409450 = (9172 * 100000) / 10936 + 325581
0x0|0h,0xff|0h,0x7f|80h,0xff|1h,0x0|0h,0x7|91h,0x60|abh,0x64|0h,0x1c|0h,0xcb|16h,0xff|70h,0xff|73h,0x0|2h,0x60|b1h,0x60|d6h,0x7|91h,0x7|d0h,0x6d|c9h,0xa0|5ah,0x0|0h,0x2|90h,0x1|48h,0x16|e5h,0x0|1h,0x7|d0h,0xc9|6ah,0x1c|16h,0xcf|c2h,0x0|feh,0x23|14h,0x2|80h,0x7|8fh,0x4d|78h,0x0|92h,0x1|0h,0x7|d0h,0x14|0h,0x23|5h,0x16|0h,0x7f|ceh,0x0|7h,0x8e|84h,0x10|3bh,0x8|10h,0xe3|e1h,0x29|eh,0x40|0h,0x0|0h,0x4|0h,0x6|40h,0x8|0h,0x0|0h,0x5|52h,0x7|d4h,0x1|0h,0x5|e0h,0x0|78h,0x10|25h,0x50|30h,0x6|0h,0x16|80h,0x14|0h,0x5|deh,0xe0|0h,0x10|0h,0x4|10h,0x7f|ffh,0x0|0h,0xcf|0h,0x1|f4h,0x32|0h,0x0|0h,0x60|abh,0xe2|cfh,0x7|91h,0xf3|0h,0xff|fch,0xff|fch,0xba|cfh,0x23|c5h,
0xc|47h,0xb|c2h,0x0|1h,0x16|7dh,0x0|3h,0x0|6h,0xff|90h,0xff|ffh,0x4c|10h,0x0|0h,0x4c|30h,0xff|c0h,0x40|0h,0x0|0h,0xce|a0h,0x9|10h,0x0|0h,0x0|0h,0x0|0h,0x0|0h,0x0|0h,0x0|0h,0x60|b1h,0xff|47h,0x3f|e7h,0x55|71h,0xff|f3h,0xce|9bh,0x0|76h,0x39|10h,0xcb|16h,0x60|abh,
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL2:0x1a
init_microusb_ic: MUIC: CONTROL2:0x3a
reading nps status file is successfully!.
nps status=0x504d4f43
PMIC_IRQSRC = 0x0
PMIC_IRQ1 = 0xb
PMIC_IRQ2 = 0x1b
PMIC_IRQ3 = 0x0
PMIC_IRQ4 = 0x11
PMIC_STATUS1 = 0x1
PMIC_STATUS2 = 0x10
PMIC_STATUS3 = 0x0
PMIC_STATUS4 = 0x0
bootloader base address=0x4d400000
LPDDR0 1st. cached=0x40000000, size=0xe400000
LPDDR0 non-cached=0x4e400000, size=0xa00000
LPDDR0 2nd. cached=0x4ee00000, size=0x1200000
RST_STAT = 0x10000
get_hwrev() = 8
board_process_platform: MAGIC c0c0c0c0 at 40000000!
board_process_platform: debug level is 574f4c44!
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
hw_pm_status: jig_status = 1, chg_status = 0
s5p_set_high_clk: ARM Clock = 800MHz.
......kernel is non signed binary.
a2, 83, 1f, lcdtype = 0
Autoboot (0 seconds) in progress, press any key to stop
boot_kernel: debug level low!
checkbit: find RECOVERY
checkbit (0)
......kernel is non signed binary.
ATAG_CORE: 5 54410001 0 0 0
MEMCONFIG: 20e01323 20e01323
ATAG_MEM: 4 54410002 10000000 40000000
ATAG_MEM: 4 54410002 10000000 50000000
ATAG_MEM: 4 54410002 10000000 60000000
ATAG_MEM: 4 54410002 10000000 70000000
ATAG_SERIAL: 4 XXXXXXXX XXXXXXXX XXXXXXXX
ATAG_REVISION: 3 54410007 8
ATAG_CMDLINE: 33 54410009 'loglevel=4 console=ram sec_debug.enable=0 sec_debug.enable_user=0 c1_watchdog.sec_pet=5 sec_log=0x100000@0x5ea00000 s3cfb.bootloaderfb=0x5ec00000 lcdtype=3 consoleblank=0 lpj=3981312 vmalloc=144m'
ATAG_NONE: 0 0
Starting kernel at 0x40008000...
h2. Available commands
SBL> help
Following commands are supported:
* movichk
* setenv
* saveenv
* printenv
* help
* reset
* boot
* kernel
* loadpart
* loadkernel
* erasepart
* format
* open
* close
* eraseall
* showpart
* addpart
* delpart
* savepart
* nkernel
* nandread
* nandwrite
* usb
* crc
* log
* sud
* upload
* emmc
* smartreport
* keyread
* readadc
* mmctest
* usb_read
* usb_write
* fuelgauge
* wdt
To get commands help, Type "help "
And their respective help
SBL> help movichk
* Help : movichk
* Usage :
SBL> help setenv
* Help : setenv
* Usage : setenv [name] [value] . .
Modify current environment info on ram
SBL> help saveenv
* Help : saveenv
* Usage : saveenv
Save cuurent environment info to flash
SBL> help printenv
* Help : printenv
* Usage : printenv
Print current environment info on ram
SBL> help help
* Help : help
* Usage : help [command]
SBL> help reset
* Help : reset
* Usage : reboot
Reboot system
SBL> help boot
* Help : boot
* Usage : boot [kernel options]
Boot Linux with optional kernel options
SBL> help kernel
* Help : kernel
* Usage : kernel hex_adr
Change the Linux kernel base
SBL> help loadpart
* Help : loadpart
* Usage : load partition from storage device.
SBL> help loadkernel
* Help : loadkernel
* Usage : load kernel from storage device.
SBL> help erasepart
* Help : erasepart
* Usage : erase partition.
SBL> help format
* Help : format
* Usage : format
format device
SBL> help open
* Help : open
* Usage : open
open device
SBL> help close
* Help : close
* Usage : close
close device
SBL> help eraseall
* Help : eraseall
* Usage : eraseall
erase all units
SBL> help showpart
* Help : showpart
* Usage : showpart
show partition information
SBL> help addpart
* Help : addpart
* Usage : addpart
add partition information
- ex) addpart 0x(id) 0x1(attr) 0x10(units)
SBL> help delpart
* Help : delpart
* Usage : delpart
delete last partition information
SBL> help savepart
* Help : savepart
* Usage : savepart
save partition information
SBL> help nkernel
* Help : nkernel
* Usage : nkernel command
* Usage : nkernel
read kernel from flash to DDR
SBL> help nandread
* Help : nandread
* Usage : * Usage : nandread
read partition from flash to SDRAM(0x80000000)
SBL> help nandwrite
* Help : nandwrite
* Usage : * Usage: nandwrite
write partition from SDRAM(0x80000000) to flash
SBL> help usb
* Help : usb
* Usage : usb download command
SBL> help crc
* Help : crc
* Usage : crc
SBL> help log
* Help : log
* Usage : print log
SBL> help sud
* Help : sud
* Usage : sud command
SBL> help upload
* Help : upload
* Usage : upload
SBL> help emmc
* Help : emmc
* Usage : emmc
SBL> help smartreport
* Help : smartreport
* Usage : smartreport [mode]
SBL> help keyread
* Help : keyread
* Usage : *Usage : keyread
SBL> help readadc
* Help : readadc
* Usage : *Usage : readadc
SBL> help mmctest
* Help : mmctest
* Usage : mmctest
SBL> help usb_read
* Help : usb_read
* Usage : usb_read reg
Read the usb ic register
SBL> help usb_write
* Help : usb_write
* Usage : usb_write reg, val
Read the usb ic register
SBL> help fuelgauge
* Help : fuelgauge
* Usage : *usage : fuelgauge
SBL> help wdt
* Help : wdt
* Usage : wdt