Project

General

Profile

UART » History » Version 73

Denis 'GNUtoo' Carikli, 03/10/2020 04:11 PM
fix copy typo

1 40 Denis 'GNUtoo' Carikli
h1. UART
2 1 Denis 'GNUtoo' Carikli
3 12 Denis 'GNUtoo' Carikli
There is an in-depth article covering several Samsung devices in the [[SamsungSerial]] page
4 11 Denis 'GNUtoo' Carikli
5 1 Denis 'GNUtoo' Carikli
h2. Settings
6 12 Denis 'GNUtoo' Carikli
7 31 Denis 'GNUtoo' Carikli
|_. Device and documentation |_. I/O voltage |_. ID<->GND |_. SOC TX |_. SOC RX |_. switch |_. stock bootloader settings |_. Comments |
8 73 Denis 'GNUtoo' Carikli
| GT-I9000 | 1.8V[8] ? | 150k | D- | D+ | | *UART settings*: 115200 8N1  | |
9 71 Denis 'GNUtoo' Carikli
| GT-I9100 | 1.8V[8] ? | 510k[9] | D- | D+ | "MAX8997":https://git.replicant.us/replicant/kernel_samsung_smdk4412/tree/arch/arm/configs/lineageos_i9100_defconfig#n1294 | *UART settings*: ttySAC2 115200 8N1 
10 58 Denis 'GNUtoo' Carikli
 To get the UART enabled at boot with the stock bootloader:
11 57 Denis 'GNUtoo' Carikli
* Power the phone off and remove the battery
12
* Put a battery in
13 62 Denis 'GNUtoo' Carikli
* Hold the select button
14 57 Denis 'GNUtoo' Carikli
* Plug the UART
15 70 Denis 'GNUtoo' Carikli
* Release the select button
16
To get the UART enabled at boot with the Replicant 6.0 kernel and the stock bootloader, see the "DHylands_SGS2_Console":https://wiki.mozilla.org/DHylands_SGS2_Console page on the mozilla wiki. | At some point the boot procedure switches to the modem UART, it's probably some linux driver doing that |
17 71 Denis 'GNUtoo' Carikli
| GT-N7000 | 1.8V[8] ? | 510k[9] | D- | D+ | | *UART settings*: 115200 8N1 | |
18 1 Denis 'GNUtoo' Carikli
| GT-I9100G_CHN_CHN | 1.8V[8] ? | 619k[9] | D- | D+ | ? | *UART settings*: 115200 8N1 | Very few prints from Xloader, the next bootloader used by Android 2.6.3 doesn't seem to print much |
19
| GT-I9300 |/2. 1.8V[1] |/4. 619 kOhms[3] |/4. D- |/4. D+ |/4. MAX77693[5] |/4. *UART settings*: 115200
20 62 Denis 'GNUtoo' Carikli
To increase verbosity during boot:
21
* Power off the phone and remove the battery
22
* Put a battery in
23
* Press the hold the volume-down button
24
* Plug the UART and wait for the first lines to be printed
25
* Release the volume-down button |/2. It gives a shell once Replicant 6 has booted |
26 48 Denis 'GNUtoo' Carikli
| GT-I9305 |
27
| GT-N7100 | ? | |
28
| GT-N7105 | ? | |
29 61 Denis 'GNUtoo' Carikli
| [[GalaxyNexusI9250SerialConsole|Galaxy Nexus (GT-I9250)]] | | 619 kOhms[4] | D+ | D- | FSA9480[7] | UART settings:
30
* By default: ttyFIQ0, 115200 8N1
31
* After patching Linux: ttyO2, 115200 8N1
32 43 Denis 'GNUtoo' Carikli
See [[GalaxyNexusI9250SerialConsole]] for more details. | |
33 45 Denis 'GNUtoo' Carikli
| [[NexusSI902xSerial|Nexus S]] | | 150 kOhm | | | FSA9480 | | |
34 48 Denis 'GNUtoo' Carikli
| [[OptimusBlackSerial|Optimus Black (P970)]] | 1.8V[6] | N/A[2] | | | DP3T | | |
35 60 Denis 'GNUtoo' Carikli
| ODROID-U3, console UART | 1.8V |\4. "connector":https://wiki.odroid.com/accessory/development/usb_uart_kit#odroid_port_description_of_uart_connector | *UART settings*: ttySAC1, 115200 8N1 | |
36
| ODROID-U3, IO pins UART | 1.8V |\4. "connector":https://wiki.odroid.com/old_product/odroid-x_u_q/odroid_u3/u3_ioport_uart | *UART settings*: ttySAC0, 115200 8N1 | |
37 17 Denis 'GNUtoo' Carikli
38 1 Denis 'GNUtoo' Carikli
fn1. Measured between USB GND and USB VCC
39
40
fn2. Code is required to use the switch as you need to configure both the MUIC and DP3T switch
41
42
fn3. See "The related driver source code":https://git.replicant.us/replicant/kernel_samsung_smdk4412/tree/drivers/misc/max77693-muic.c#n102
43
44
fn4. See the "postmarketOS wiki page on Serial debugging":https://wiki.postmarketos.org/wiki/Serial_debugging
45 30 Denis 'GNUtoo' Carikli
46 1 Denis 'GNUtoo' Carikli
fn5. See the "driver":https://git.replicant.us/replicant/kernel_samsung_smdk4412/tree/drivers/misc/max77693-muic.c and the "ifixit teardown":https://www.ifixit.com/Teardown/Samsung+Galaxy+S+III+Teardown/9391
47
48
fn6. Reference: [[OptimusBlackSerial]]
49 44 Denis 'GNUtoo' Carikli
50
fn7. See "board-tuna-connector.c":https://git.replicant.us/replicant/kernel_samsung_tuna/tree/arch/arm/mach-omap2/board-tuna-connector.c "fsa9480.c":https://git.replicant.us/replicant/kernel_samsung_tuna/tree/drivers/misc/fsa9480.c in "kernel_samsung_tuna":https://git.replicant.us/replicant/kernel_samsung_tuna
51 50 Denis 'GNUtoo' Carikli
52
fn8. Works, as it was tested on the device. TODO: measure the voltage, as lower UART voltages often works with higher voltage levels.
53
54
fn9. Works, as it was tested on the device. TODO: look the official reference in the driver for it.
55 23 Denis 'GNUtoo' Carikli
56 47 Denis 'GNUtoo' Carikli
h2. Datasheets
57
58
* "FSA9480.pdf":https://media.digikey.com/pdf/Data%20Sheets/Fairchild%20PDFs/FSA9480.pdf
59
60 23 Denis 'GNUtoo' Carikli
h2. Interesting links
61
62 34 Denis 'GNUtoo' Carikli
* There is a "page on Serial debugging":https://wiki.postmarketos.org/wiki/Serial_debugging on the postmarketOS wiki that contains information for using the serial port for many smartphones models.
63
* "mv-uart":https://osmocom.org/projects/mv-uart/wiki A serial port adapter with configurable voltages (and GPIOs)
64 53 Denis 'GNUtoo' Carikli
* "DHylands_SGS2_SerialAdapter":https://wiki.mozilla.org/DHylands_SGS2_SerialAdapter : A very compact setup but with fixed resistor value.
65 68 Denis 'GNUtoo' Carikli
66
h2. See also
67
68 69 Denis 'GNUtoo' Carikli
* [[BootloaderInterfaces]]: Documentation about the stock bootloaders interfaces